Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - AndehX

Pages: [1]
1
I'd set it to off when I originally installed the audio fix pcb as that was the point of installing it to begin with.

2
yeah, I can't remember who I bought the PCB fix off of, but he obviously either didn't check his soldering, or just completely forgot to solder that pin.  All good now though.  I have the audio boost turned off too.
Working on my own personal Super Metroid MSU-1 pack.  Bit tedious having to "normalise" all the music, but the result is pretty cool

3
Well that was a bit anti-climactic...  Turns out one of the pins on the TS922 chip (Output 1 to be exact) wasn't soldered.  I've had this installed in my SD2SNES for almost 2 years now, and only just noticed this issue with MSU-1 audio /facepalm.

Anyway.  I guess this could be useful if anyone else has a similar issue.  Check your soldering.

4
I have a strange issue I've only recently noticed.  The left channel is louder than the right channel when playing MSU-1 audio.  Sound effects are unaffected.
I have a Rev. F. SD2SNES with the MSU-1 audio fix pcb by borti4938.  Any ideas what could cause this?

5
EverDrive N8 / Re: CHR Error 01
« on: July 19, 2017, 09:53 PM »
Anyone know what issues with the console can cause this?  CHR error 01?  bad PPU or SRAM?
It tests cartridge CHR ram. It might be some problem with ppu address bus
well I picked up a cheap NES on ebay (has flashing red light issue) so I'll get to the bottom of the issue.

6
EverDrive N8 / Re: CHR Error 01
« on: July 19, 2017, 04:24 PM »
ok i got my replacement everdrive today and it has the exact same issue.  This leads me to believe it might be an issue with my console.  Anyone know what issues with the console can cause this?  CHR error 01?  bad PPU or SRAM?

Edit:  Ok, I have a faulty console.  I desoldered the WRAM and VRAM and swapped them over, and now I get garbled text all over the place.  Strange thing is, I can now sometimes get games to start up, but graphics is messed up, so it looks like im going to have to source a different console.

7
EverDrive N8 / Re: CHR Error 01
« on: July 17, 2017, 03:47 PM »
Also curious... Should I really be getting hardware revisions from 2013?  I mean that was 4 years ago... Has there been no hardware revisions since then?

8
EverDrive N8 / Re: CHR Error 01
« on: July 15, 2017, 01:59 AM »
Yeah I've bought a number of flash carts from Retrotowers (SD2SNES, Everdrive GG, Everdrive MD, Everdrive 64 v3) and had no issues with any of them.  This is the first one I've had problems with.  It started acting up this morning, and I managed to get it to work periodically, then it stopped working altogether after that... :/

9
FXPAK (SD2SNES) / Re: SD2SNES June 2016 re-stock PCB revision?
« on: July 14, 2017, 11:09 PM »
Upgraded mine using Borti's PCB.  Had no issues and it works like a charm!  (Rev F.)


10
EverDrive N8 / Re: CHR Error 01
« on: July 14, 2017, 10:55 PM »
Aw man, it was working fine just this morning too  :-\

I'm going to see if Retrotowers.co.uk will replace it for me first.  I'll keep you updated.

11
EverDrive N8 / Re: CHR Error 01
« on: July 14, 2017, 09:29 PM »
Sure, here you go:






12
EverDrive N8 / CHR Error 01
« on: July 14, 2017, 09:01 PM »
So my Everdrive has been working for a few days now since I bought it, but today it's started showing weird yellow pixels in the menu text, and launching a game results in a grey screen.  Self test shows CHR Error 01 (sometimes 02)

Has it become faulty?  Should I return it for a replacement?  (bought from Retrotowers.co.uk)

Pages: [1]